Supermicro X7DBP-8
Motherboard
- Storage:
- ESB2 SATA Controller
- RAID 0, 1, 5, 10 support (Windows Only)
- RAID 0, 1, 10 support (Linux)
- SCSI: Adaptec AIC-7902 Controller
- Dual-Channel Ultra320 SCSI (Host RAID only supports 4
drives)
- Host RAID 0, 1, 10 support
- Support for Zero-Channel RAID
- RAID 0, 1, 5, 10
- Optional: (Card NOT included)
- Support for Intelligent Platform Management Interface
v.2.0
- 200-pin IPMI slot (SIMLP)
- (Optional: AOC-SIM1U-3B(+) and AOC-SIM1U-3D)
- Rear Panel I/O Ports:
- Super I/O: Winbond 83627HF chip
- Clock Generator: CK410B chip
- Six Serial ATA ports
- Six SATA hard drives supported
- Single EIDE channel support up to two UDMA IDE devices
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
- 1 Floppy controller; 1.44 MB
- 2x RJ45 LAN port
- 2x USB rear ports
- 2x USB internal headers, 1 dual, 1 single
- USB 2.0 Compliant / 1.1 Compliant
- 1x VGA Port
- PS/2 keyboard and mouse ports
- 2 Fast UART 16550 serial ports
- Hardware Monitoring:
- Monitors for CPU Cores, +3.3V, +5V, ±12V, +5V Standby,
VBAT
- CPU Core 5-Phase-switching voltage regulator with
auto-sense from 0.86V-1.63V
- FAN: Total of ten proprietary fan headers for up to ten
fans
- Ten fans with tachometer status monitoring
- Status monitor for speed control
- Status monitor for on/off control
- Low noise fan speed control
- Temperature: Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Control for 8x fan connectors
- I2C temperature sensing logic
- Thermal Monitor 2 (TM2) support
- CPU / System Overheat LED
- Chassis intrusion detection
- Chassis intrusion header
- SDDC Support
- RoHS
- Environmental Spec.: Operating Temperature: 10 °to 35 °C
(50 °to 95 °F)
- Non-operating Temperature: -40 °to 70 °C (-40 °to 158 °F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95%
(non-condensing)
|
Motherboard Specifications
- Model:
- Supermicro X7DBP-8 Motherboard
- Processor Support:
- Dual 771-pin LGA Sockets
- Supports up to two Intel ® 64-bit Xeon ®processor(s)
of the same
- type below: Quad-Core Intel ® Xeon ®Processor 5400/5300
sequence (Harpertown/Clovertown processor) up to 3.16 GHz
- Dual-Core Intel ® Xeon ®Processor 5200/5100/5000 sequence
(Wolfdale/Woodcrest/Dempsey processor) up to 3.40 GHz
- Chipset:
- Intel ® 5000P (Blackford) chipset
- MCH + PXH + ESB2
- FSB:
- 1333 / 1066 / 667 MHz system bus
- Memory:
- Eight 240-pin DIMM sockets
- Supports up to 32 GB 667/533MHz FB-DIMM memory
- Dual branch memory bus
- Memory must be populated in pairs
- 667/533MHz FB-DIMM (Fully Buffered DIMM) ECC SDRAM
72-bit, 240-pin gold-plated DIMMs
- 512 MB, 1GB, 2GB, 4GB
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
- Supports Intel ® x4 Single Device Data Correction (SDDC)
- Expansion Slots:
- 1 (x8) PCI-e slot OR 1x 64-bit 100MHz PCI-X (3.3V) slot
- 1 (x8) PCI-e slot OR 1x 64-bit 133MHz PCI-X (3.3V) slot
- 1 SIM1U Slot (IPMI 2.0) (Supermicro Intelligent
Management)
- On-Board Video:
- ATI ES1000 controller with 16 MB of video memory
- On-Board LAN:
- Intel ® (ESB2/Gilgal) 82563EB Dual-Port Gigabit Ethernet
Controller
- Supports 10BASE-T, 100BASE-TX, and 1000BASE-T, RJ45
output
- Intel ® I/OAT support for fast, scaleable, and
reliable networking
- Form
Factor/Dimensions:
- Proprietary
- 16.24" Length x 11.23" Width (41.25cm x 28.52cm)
- Manageability:
- Optional IPMI (Intelligent Platform Management
Interface) 2.0 / 1.5 - with Virtual Media 8
- Optional KVM over LAN & 3rd LAN Port
- NMI
- ACPI Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode for AC power recovery
- Internal/External modem remote ring-on
- BIOS:
- 8Mb Flash EEPROM with Phoenix ® BIOS
- Features: Plug and Play (PnP)
- SMBIOS 2.3
- APM 1.2
- DMI 2.3
- PCI 2.2
- ACPI 1.0
- ACPI 1.0 (limited)
- USB Keyboard support
- Hardware BIOS Virus protection
- Special Features:
- Operating System Software: Supports 64-bit Operating
Systems
- Supports 32-bit Operating Systems
- Important Chassis Notes: To ensure system stability, a
500W (minimum) ATX power supply [4-pin (+12V), 8-pin (+12V) and 24-pin
are required]
|
